Posts | Comments

Planet Arduino

Archive for the ‘Reflow’ Category

There are few scenes in life more moving than the moment the solder paste melts as the component slides smoothly into place. We’re willing to bet the only reason you don’t have a reflow oven is the cost. Why wouldn’t you want one? Fortunately, the vastly cheaper DIY route has become a whole lot easier since the birth of the Reflowduino – an open source controller for reflow ovens.

This Hackaday Prize entry by [Timothy Woo] provides a super quick way to create your own reflow setup, using any cheap means of heating you have lying around. [Tim] uses a toaster oven he paid $21 for, but anything with a suitable thermal mass will do. The hardware of the Reflowduino is all open source and has been very well documented – both on the main hackaday.io page and over on the project’s GitHub.

The board itself is built around the ATMega32u4 and sports an integrated MAX31855 thermocouple interface (for the all-important PID control), LiPo battery charging, a buzzer for alerting you when input is needed, and Bluetooth. Why Bluetooth? An Android app has been developed for easy control of the Reflowduino, and will even graph the temperature profile.

When it comes to controlling the toaster oven/miscellaneous heat source, a “sidekick” board is available, with a solid state relay hooked up to a mains plug. This makes it a breeze to setup any mains appliance for Arduino control.

We actually covered the Reflowduino last year, but since then [Tim] has also created the Reflowduino32 – a backpack for the DOIT ESP32 dev board. There’s also an Indiegogo campaign now, and some new software as well.

If a toaster oven still doesn’t feel hacky enough for you, we’ve got reflowing with hair straighteners, and even car headlights.

Ott
17

Reflow Master Shield – Arduino Solder Reflow Oven

arduino, Reflow, shield, soldering Commenti disabilitati su Reflow Master Shield – Arduino Solder Reflow Oven 

Turn your toaster oven into your own solder reflow factory shop using the Reflow Master Shield!!!

The Reflow Master Shield from Paladin Enabling Technologies is an Arduino shield that turns your normal toaster oven into a reflow oven. A reflow oven is used in the production of electronics to change solder paste from a paste form to a liquid form and lastly to a solid form. This results in all your components being soldered for you in one run.

But let me share with you why I’ve created the Reflow Master Shield and why you would want one.

Reflow Master Shield – Arduino Solder Reflow Oven - [Link]

Set
13

Temperature controlled reflow oven build

arduino, PID, Reflow, reflow oven, soldering Commenti disabilitati su Temperature controlled reflow oven build 

IMG_1187-Copy

Matt of SkyLabs has a nice build log about a temperature controlled reflow oven he built using an Arduino based PID controller and a standard toaster oven:

We have successfully managed to build a temperature controlled reflow oven using an Arduino based PID controller and a standard toaster oven from Robert Dyas! This is a must have accessory for any hobbyist who regularly uses surface mount components within their designs. Below we have a build log documenting the process of constructing the oven including:
Teardown of the original oven
Custom enclosure construction
Control Methods
Arduino Installation

So to start off I will outline a basic parts list of what I used:
Arduino Uno
Reflow Oven Shield
Solid State Relay
K-Type Thermocouple
230v AC to 5v DC Power Supply
Custom Laser Cut Enclosure

[via]

Temperature controlled reflow oven build - [Link]

Giu
18

Reflow Oven Controller with graphics TFT

arduino, control, controller, JD-T1800, Oven, PID, Reflow, ST7735R, TFT Commenti disabilitati su Reflow Oven Controller with graphics TFT 

CycleWithOverflow

0xPIT @ github.com writes:

This Reflow Oven Controller relies on an Arduino Pro Micro, which is similar to the Leonardo and easily obtainable on eb*y for less than $10, plus my custom shield, which is actually more like a motherboard.

As I believe it is not wise to have a mess of wiring and tiny breakout-boards for operating mains powered equipment, I’ve decided to design custom board with easily obtainable components.

The hardware can be found in the folder hardware, including the Eagle schematics and PCB layout files. It should fit the freemium version of Eagle

Reflow Oven Controller with graphics TFT - [Link]

Nov
20

Reflow toaster oven using an Arduino

arduino, Oven, Reflow, RF, servo, transmitter Commenti disabilitati su Reflow toaster oven using an Arduino 

Ray Wang writes:

Hi, I recently built a reflow toaster oven using an Arduino. I know it’s pretty standard stuff, but my version has an automatic oven door opener (using a servo) and circulation fan to speed up the cooling time, and remote notification using an RF transmitter

[via]

Reflow toaster oven using an Arduino - [Link]



  • Newsletter

    Sign up for the PlanetArduino Newsletter, which delivers the most popular articles via e-mail to your inbox every week. Just fill in the information below and submit.

  • Like Us on Facebook