Posts | Comments

Planet Arduino

Archive for the ‘HC-06’ Category

This was gonna happen – sooner or later. [matthewhallberg] built a “Smart” trash can that is connected to the Internet and can be controlled by its own Android App. We’re not sure if the world needs it, but he wanted one and so built it. He started it out on a serious note, but quickly realized the fun part of this build – check out his funny Infomercial style video after the break.

trash_can_02The build itself is uncomplicated and can be replicated with ease. A servo motor helps flip the lid open and close. This is triggered by an ultrasonic ping sensor, which responds when someone waves a hand in front of the trash can. A second ping sensor helps inform the user when it is full and needs to be emptied. A Leonardo with the Idunio Yun shield helps connect the trash can to the internet. An mp3 shield connected to a set of powered computer speakers adds voice capability to the trash can, allowing it to play back pre-recorded sound clips. Finally, a Bluetooth module lets him connect it to an Android phone and the companion app controls the trash can remotely.

For the IoT side of things, [matthewhallberg] uses a Temboo account to send an email to the user when the trash can is full. The Arduino sketch, a header file to configure the Temboo account, and the Android application can all be downloaded from his blog. If this project inspires you, try building this awesome Robotic trash can which catches anything that you throw near it  or read the barcodes off the trash being thrown out and update the grocery list.


Filed under: Arduino Hacks, home hacks, internet hacks
Ott
30

DIY LED Matrix Display with Bluetooth support

arduino, bluetooth, HC-06, LED, matrix Commenti disabilitati su DIY LED Matrix Display with Bluetooth support 

ReyPlaying

LED matrices are a popular mean of displaying text, graphics, and animated information at gas stations, convenient stores, and many other public places. Raj’s new project is about making a Bluetooth-enabled 8×64 LED matrix display, where you can send the text messages through a smartphone over a Bluetooth connection. He used Arduino as the main controller and an HC-06 Bluetooth adapter to receive data from the smartphone. He has shared all of his design files and Arduino firmware on his blog.

DIY LED Matrix Display with Bluetooth support - [Link]

Ago
28

BridgeDuino: A wireless Arduino HUB and shield

arduino, arduino uno, BridgeDuino, FS1000A, hc-05, HC-06, nRF24L01+, RF433Mhz Commenti disabilitati su BridgeDuino: A wireless Arduino HUB and shield 

6793067_orig-600x436

TechBitar shared his latest project the BridgeDuino with boards from DirtyPCBs:

BridgeDuino is a Swiss army knife PCB for rapid networking of inexpensive wireless communication modules. Breadboards are super for one-off experiments. But after prototyping half a dozen wireless prototypes involving more than just two Arduinos, the wiring mistakes and associated debugging grew more time consuming.
I also wanted a PCB that can act as a shield to Arduino Uno as well as work with the inexpensive and low-power Arduino ProMini.

As of this release, BridgeDuino supports the following wireless technologies/modules:
IR Transmiter LED 940nm
IR Receive 38Khz
RF433Mhz Receiver
RF433Mhz FS1000A Transmitter
Bluetooth HC-06 & HC-05
Nrf24L01+

[via]

BridgeDuino: A wireless Arduino HUB and shield - [Link]

SmartLitterBox

How can you not be interested in a project that uses load cells, Bluetooth, a Raspberry Pi, and Twitter. Even for those of our readers without a cat, [Scott's] tweeting litter box is worth the read.

Each aspect of this project can be re-purposed for almost any application. The inexpensive load cells, which available from eBay and other retailers, is used to sense when a cat is inside the litter box. Typically sensors like the load cell (that contain a strain gauge) this use a Wheatstone bridge, which is very important for maximizing the sensitivity of resistive sensor. The output then goes to a HX711, which is an ADC specifically built for load cells. A simple alternative would be using an instrumentation amplifier and the built-in ADC of the Arduino. Now, the magic happens. The weight reading is transmitted via an HC-06 Bluetooth module to a Raspberry Pi. Using a simple Perl script, the excreted weight, duration, and the cat’s resulting body weight is then tweeted!

Very nice work! This is a well thought out project that we could see being expanded to recognize the difference between multiple cats (or any other animal that goes inside).


Filed under: Arduino Hacks, Raspberry Pi, wireless hacks


  • Newsletter

    Sign up for the PlanetArduino Newsletter, which delivers the most popular articles via e-mail to your inbox every week. Just fill in the information below and submit.

  • Like Us on Facebook