Posts | Comments

Planet Arduino

Archive for the ‘lipo’ Category

Ott
30

Arduino Weather station

arduino, BMP085, DHT22, irradiance, lipo Commenti disabilitati su Arduino Weather station 

2013-03-17-14.48.42_small-600x450

Xose Perez of Tinkerman has written an article detailing the build of his weather station:

Arduino FIO based weather station with a DHT22 temperature & humidity sensor and a BMP085 barometric pressure sensor. The whole sensor will be powered by a solar panel (doubling as irradiance sensor) and backed by a LiPo cell.

[via]

Weather station - [Link]

Dic
10

OLED name badge with rechargeable LiPo cell

arduino hacks, badge, breakout, lipo, OLED Commenti disabilitati su OLED name badge with rechargeable LiPo cell 

oleduino-name-badge

Here’s a project that let [Rick Pannen] try his hand with an OLED display and a rechargeable power source. He calls it OLEDuino which is a mashup of the display type and the Arduino compatible chip running the whole thing. He figures it will serve nicely as a geeky name badge but also ported a Breakout type game to play when he’s bored.

The project is an inexpensive way to attempt a more permanent trinket than simply using Arduino and a breadboard. [Rick] sourced the OLED display and USB LiPo charging cable on eBay. The ATmega328 hiding below the display is being driven from the 3.7V LiPo cell without any power regulation. The four buttons at the bottom provide the only user input but it should be more than enough for a few simple tricks.

Head over to his code repo for a bit more information. The schematic and board are both Eagle files. We generated an image of the schematic and embedded it after the break if you want to take a quick look at how simple the hardware really is.

oleduino


Filed under: arduino hacks
Found out why the maiden flight ended with Issac Newton attacking my plane. The pilot said it seemed to loose power as she turned into the wind, and he was flat out for whole flight due to the excessive weight of all that Corriboard, I have a lighter air frame in the works 1300 Grams wing loading 12.53 oz/ft², 250 Watts per Kilo Please see the spreadsheet. I think its highly likely she just ran out of juice?

This is why I suspect the battery state



Turnigy Accucel-6 50W 6A Balancer/Charger


Spec.
Input Voltage: 11~17v
Circuit power: Max Charge: 50W / Max Discharge: 5W
Charge Current Range: .1~6.0A
Ni-MH/NiCd cells: 1~15
Li-ion/Poly cells: 1~6
Pb battery voltage: 2~20v



Some how or other my charger was set to a max CAPA of 200mAh so my batteries were never charged. My wife helpfully pointed out that I should have read the manual (Here is the manual) but that just isn't the bloke way, why do girls not get that?



Maiden flight of Yellow Plane flown by a local pilot Richard to avoid instant crash I would cause. A little tail heavy but flew pretty well on a gusty day, I'm told control was good. Ended in a crash but not too badly damaged, learned a lot. I'm just chuffed if flew looks pretty good on such a windy, which is pretty standard for the south island this time of year.


My scratch built FPV platform. Took around 30 hours to build mostly Corriboard with some ply, aluminium and carbon fiber spars. Total material cost around 50 US$. Got a DT700 (see tests data here) which hopefully will be an adequate power source. Its a modular design based around an armature, so wings and tail etc are bolted on and can be exchanged for testing parts and ideas. Have a pair of KM3 wings and the Corriboard ones shown below.


Please see the spread sheet here Yellow Plane Data 


More Links
The RX Build
Power Tests
More Test Data
Xbee's and Arduinos
Controller using Tiny CLR
Xbee Helpers


Based around a stiff wooden armature and two aluminium tail spars the wings are removable for transportation. According to my calculations the wing loading is 15.5 Oz/Ft² at a flight weight of 1700 Grams. A glass fiber nose has been molded and is curing now which is around 80 grams, which will contain the FPV gear and the main battery.


Home brew Arduino Xbee remote control 




  • Newsletter

    Sign up for the PlanetArduino Newsletter, which delivers the most popular articles via e-mail to your inbox every week. Just fill in the information below and submit.

  • Like Us on Facebook